Download Mankatha Movie Songs for Free !

Mankatha Tamil songs :-

Movie Name : Mankatha
Year : 2011
Cast : Ajith Kumar, Trisha Krishnan, Arjun, Premji Amaren, Lakshmi Rai, Vaibhav Reddy, Mahat Raghavendra, Ashwin Kakumanu, Andrea Jeremiah, Anjali...
Music Director : Yuvan Shankar Raja
Director : Venkat Prabhu
Producer : Dhayanidhi Alagiri, Vivek Rathinavel
Label : Sony Music
Lyrics : Gangai Amaren (1,6,8), Niranjan Bharathi (2), Padmasree Kavingar Vaali (3,4,5)
English Lyrics : Yuvan Shankar Raja
Hindi Lyrics : Sucharita

1. Vilayaadu Mankatha - Yuvan Shankar Raja, Ranjith, Sucharita, Premgi Amaren, Anita
2. Nee Naan - SP Charan, Bhavatharani 
3. Vaada Bin Laada - Krish, Suchitra 
4. Machi Open The Bottle - Mano, Premgi Amaran, Tippu, Haricharan, Naveen 
5. Nanbane - Madhusree, Yuvan Shankar Raja 
6. Balle Lakka - Karthik, Vijay Yesudas, Anusha Dhayanidhi 
7. Mankatha Theme Music
8. Vilayaadu Mankatha (Extended Dance Mix) - Premgi Amaren 

Click on the below link to Download now.
DOWNLOAD NOW !

Switching Regulators

Step-Up and Inverting Switching Regulators

             The switching regulator shown in Figure 9-3 is a step-down regulator—Vo is smaller in value than VIN. Figure 9-5 shows two other types of regulators, a step-up and an inverting regulator. The step-up regulator produces a regulated voltage VO that is greater in value than VIN, while the inverting regulator produces a Vo that is inverted in polarity from VIN. A positive VIN produces a negative Vo.

Switching Regulator Design

 

                The design of switching regulators can be accomplished in a number of ways, but they all include the inductor as the temporary energy storage element and large storage capacitors. The inductor and capacitor(s) cannot be integrated into ICs; therefore they are external to any ICs used. Any of the other components, depending on the current and voltage requirements, can at least be partially integrated circuits. For example, if the current handling is within the range of 1–2 amperes, all of the error amplifier, PWM circuit, oscillator, and the control element can be one IC. With higher current requirements, external heat-sinked driver packages can be used for the control element. Resistor dividers are always used to sample the output voltage to feed back to the error amplifier.

Transformed PWM Regulators

In a different design than that shown in Figure 9-3, the PWM circuit, which contains the error amplifier, oscillator, voltage reference and some protection circuits, is used as an AC source. This AC source is transformedto the desired voltage, filtered, and fed back to the error amplifier to close the regulation loop. Such a regulator is similar to the ones described because it uses PWM pulses for regulation control, but it does not utilize the inductor as a temporary storage element. An increased pulse width (larger ON time) will increase the voltage out from the transformed source; while a decreased pulse width decreases the voltage output.

Switching Regulators

Step-Up and Inverting Switching Regulators

             The switching regulator shown in Figure 9-3 is a step-down regulator—Vo is smaller in value than VIN. Figure 9-5 shows two other types of regulators, a step-up and an inverting regulator. The step-up regulator produces a regulated voltage VO that is greater in value than VIN, while the inverting regulator produces a Vo that is inverted in polarity from VIN. A positive VIN produces a negative Vo.

Switching Regulator Design

                The design of switching regulators can be accomplished in a number of ways, but they all include the inductor as the temporary energy storage element and large storage capacitors. The inductor and capacitor(s) cannot be integrated into ICs; therefore they are external to any ICs used. Any of the other components, depending on the current and voltage requirements, can at least be partially integrated circuits. For example, if the current handling is within the range of 1–2 amperes, all of the error amplifier, PWM circuit, oscillator, and the control element can be one IC. With higher current requirements, external heat-sinked driver packages can be used for the control element. Resistor dividers are always used to sample the output voltage to feed back to the error amplifier.

Transformed PWM Regulators

In a different design than that shown in Figure 9-3, the PWM circuit, which contains the error amplifier, oscillator, voltage reference and some protection circuits, is used as an AC source. This AC source is transformedto the desired voltage, filtered, and fed back to the error amplifier to close the regulation loop. Such a regulator is similar to the ones described because it uses PWM pulses for regulation control, but it does not utilize the inductor as a temporary storage element. An increased pulse width (larger ON time) will increase the voltage out from the transformed source; while a decreased pulse width decreases the voltage output.

Actual Regulation

 

               Producing more or less voltage across the load is based upon modulating the time that the control element is closed. This is accomplished by the pulse-width modulator (PWM) driven by the error amplifier. An oscillator produces the start of pulses at a constant rate, but the end of the pulse is determined by the voltage supplied by the error amplifier. The relationship of the control voltage from the error amplifier to the pulse width that turns on the switch is shown in Figure 9-4. Note the center of the figure has a line that represents a constant level of the control voltage B that is the nominal voltage level at the rated current output. The pulse width for this control voltage is shown as width C. When the demand for current increases, the pulse width increases because the ON time of the pulse is increased. More energy is stored in the inductor so that the increased current can be supplied and the voltage maintained. The integration of the current pulses by the output filter establishes the output voltage level. More ON time in the pulses produces a higher voltage, less ON time in the pulses produces a lower voltage. As shown in Figure 9-4, when minimum current is required the pulse width is narrow with a short ON time.

Likewise, when maximum current is required the pulse width is wide with a long ON time. Here is a description of the regulation in simple terms. When the load demands more current the output voltage tends to decrease. This voltage decrease is sampled and converted to an error voltage that increases the control voltage B and increases the ON time of the pulses. The increase in ON time supplies the increased current and raises the output voltage to its required value. A load that demands less current would tend to increase the output voltage. The voltage increase is sampled and converted to an error voltage that decreases the control voltage B and decreases the ON time of the pulse. The decrease in ON time of the pulses lowers the voltage and satisfies the demand for less current. Switching regulators operate at frequencies from 100 kHz to several million cycles/sec. Because of the range of frequencies and the switching action, there is some concern about RFI energy; and attention must be paid to the shielding of sensitive circuits.